Compliance With Following International Standards: ASTM C403, IS:8142, IS:1199-part 7 Used to determine the elapsed time between batching of a concrete sample and when it is deemed by standard methods to have set. The method involves measuring the penetration resistance of a test sample, which has had coarse particles removed at periodic intervals. It is particularly useful, in determining the effect on setting time of admixtures in the concrete, where these may have been introduced specifically to increase the setting time. Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance With Following International Standards: EN 12390‑4, ASTM C39, AASHTO T22, IS : 14858 (2000) Once the machine has been switched on, the specimen positioned and centered, the only required operations are Set test parameters-including load rate: Press the start button Tighten the pressure valve The machine automatically: starts the rapid approach; switches to the test speed once the specimen comes into contact with the upper platen; automatically stops the motor upon specimen failure Release the pressure valve The test execution conforming to Standards can be easily proved. Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance With Following National / International Standards: ASTM D 88 / IS 3117 / IS 8887 The apparatus consists of stainless steel bath with oil cup which is centrally placed in a water bath. The bath has a lid which contains a water cooling tube, two handles with two stirring blades, thermometer socket and a straight heater. Stirring is done by turntable arrangement. A thermometer can also be inserted into the cup cover. Two jets one universal and one furol can be screwed to the cup by a handle (without strainer, withdrawal tube and glass wares) To work on 220V AC single phase. Temperature control by separate energy regulator. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: IS 1206 (Part II) and (Part III), ASTM D2171, ASTN D2170, EN 12596 As per IS: 1206 (Part II and III).Supplied complete with Viscosity bath with built in Digital stop watch, Vacuum Pump - capable to maintain vacuum of 300 mm/Hg, Indian Make Vacuum Manning Viscometer No.12 and 13, Reverse flow Viscometer No.6, Silicon oil, silicon tubes and calibration certificate for Viscosity bath, certificate of constant for Viscometers. Complete with instruction manual. Detailed Specification as mentioned in technical part mentioned below. Canon USA Make Glass U Tube Viscometer, Mercury Manometer, Digital Vacuum Indicator cum controller etc. are available at extra cost Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: IP 45, IS 1212, ASTM D6-90, AASHTO T-47 Purpose: The loss in bituminous material when heated is called loss on heating of bituminous material. This test is done to determine the amount of loss of bitumen by certain heating and to determine the amount of water mixed in the bituminous material. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: As per IS 1203. As per IS 1203. Basic Model with fine adjustment facility for ease of precise setting.. As per IS 1203. The apparatus consist of a cast aluminum base with an iron stand on which moves an aluminium arm. A 6" dial is fixed on this arm and a brass chromium plated rod slide through the lower portion of the arm. A needle with weights is fitted to this rod. The dial is graduated from 0‑400 in one tenth millimeter sub division. Supplied complete with adjustable needle holder, penetration needle, sample container, transfer dish and weight of 50 gm. Digital stop watch is essential to perform the test at extra cost. Model with Automatic controller and fine adjustment facility also available. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: ASTM D937, IS 1508, IS 4887, IP 179, ISO 2137 Details The Penetrometer is so designed that it permits the specified cone to drop vertically at least 40 mm and indicates accurately the depth of Penetration to nearest 0.1 mm. The Penetrometer has a platform to accommodate the test sample which can be adjusted horizontally before making the test and a mechanism for releasing the clamp of the loaded cone. The Cone is made of brass with detachable hardened steel tip, constructed to conform to the dimensions and tolerances shown in Fig. 1 of IS : 4887. The total weight of the cone and its movable attachments will be 150.0 ± 0. 1 g. The attachments consist of a rigid shaft having a suitable device at its lower end for engaging the cone. The outer surface is polished to a very smooth finish. Supplied with 1 No. each Cone, sample container and weight. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Application: Pull out anchor tester, also known as (anchor rod tension meter). Applicable to testing various anchor rods, anchor cables, steel bars, planting bars, expansion bolts, chemical anchor bolts, railway spikes, and various kinds of anchors. It can also be used for on‐site pull‐out resistance testing of glass curtain walls. It is a necessary testing instrument for each (quality inspection unit, reinforcement unit, supervision unit, university, coal mine, etc.) Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: ASTM D6521, AASHTO PPI This system is designed and made as per industrial standards T 0630-2011, Accelerated Aging Test for Bitumen by Pressure Aging Vessel in JTG E20-2011, Standard Test Methods of Bitumen and Bituminous Mixtures for Highway Engineering and SH/T 0774-2005 Standard practice for accelerated aging of asphalt binder using a pressurized aging vessel (PAV). Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: GD-0719-2 Automatic Wheel-track Tester + GD-0703-3 Wheel-Track Molding Machine. it comes with single wheel, This instrument is a single-wheel, scientific research type rutting tester, which can be used for immersion or non=immersion rutting test of the trial mold.Details as mentioned in description. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following International Standards: EN 12390-4, ASTM C39, AASHTO T22, IS : 14858 (2000) Manufactured as per International design, Plate model for highest mechanical stability, accurate centering of load and excellent repeatability. Fully Automatic pace rate control, auto stop and auto release on failure of test specimen, can be attached with flexural load frame or 500 KN load frame. attachment for Split tensile test, Modulus of Elasticity also available. Please visit YouTube video of the machine by clicking on this link https://youtu.be/9n-Ac_T_18k Note - Price and specifications mentioned here indicative only and are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: ASTM D 1559 , ASTM D 6926; AASHTO T245 It is a motor driven mechanical compactor useful for compaction in to 4" dia Marshal moulds. It is fitted with a compaction rammer weighing 4.5 kg. with a free fall of 457 mm. The rammer assembly is provided with a ratchet and pawl arrangement to lift it from the top of the test sample. When the rammer reaches the required height the pawl release the rammer which falls freely on test specimen. The release mechanism is connected by an arm moving up and down which is connected to a reduction gear coupled to the motor through another arm. An automatic blow counter fitted to the compactor is used to set the number of blows. Supplied without Moulds. - Available at extra cost Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following International Standards: EN 12390-4, ASTM C39, AASHTO T22, IS : 14858 (2000) Manufactured as per International design, Plate model for highest mechanical stability, accurate centering of load and excellent repeatability. Fully Automatic pace rate control, auto stop and auto release on failure of test specimen, can be attached with flexural load frame or additional load frame. attachment for Split tensile test, Modulus of Elasticity also available. Please visit YouTube video of the machine by clicking on this link https://youtu.be/9n-Ac_T_18k Note - Price and specifications mentioned here indicative only and are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
The instrument is in accordance with People's Republic of China Ministry of Transportation standards JTG E20-2011 Standard Test Methods for Bitumen and Bituminous Mixtures for Highway Engineering in T 0755-2011 " Slurry mixture load wheel sticky sand test " provisions of the design and manufacture of it. Suitable for controlling the upper limit of the amount of asphalt in the slurry mixture, and determining the optimum asphalt content of slurry mixture with wet wheel wear test. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance with Following International Standards: IP 72, IS 1206 and BS 3235 As per IP 72, IS 1206 and BS 3235, Electric heated with Digital Temp. Controller & Indicator with F.H.P Motor Stirrer & lighting arrangement. Supplied without Stop watch, Flask receiver and IP/ASTM Glass Thermometers. These are quoted separately and available at extra cost Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance with following international standards: IP 34, ASTM D‑93, IS ‑ 1448 and IS ‑ 1209 Basic Model. These test methods cover the determination of the flash point of petroleum products in the temperature range from 40 to 360° C by a manual Pensky Martens Closed Cup Apparatus. The apparatus serve the purpose according to IS 1209 1958 method A. The apparatus consists of a Brass Test cup with handle, removable cup cover with spring operated rotating shutter having Oil pilot jet, stirrer with flexible shaft (not-motorized). With energy regulator for temperature regulation, Suitable for operation on 220 volts AC mains. Open clip, IP Glass Thermometers, Gas test jet device available at extra cost. To Satisfy the requirements as per IS:1209 Part B and Part C, motorized stirrer and open clip are needed and available at extra cost. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Asphalt Mixer Vertical, 20lt. machine mainly consists of a main frame, variable speed mixer, elevating system, heating pot, electrical control box. The variable speed mixer consists of electric motor, gear box and vertical curved blade. The elevating system consists of a motor, worm gear, up right column,guide bar and stopper block and the heating pot has a double lever metal pot, conduction coil and electric heater. In vertical type of mixer the pot can move up and down and in the horizontal type of mixer the elevating system with agitator assembly moves up and down. Suitable for operation on 230 V, 50 Hz, 1 phase, AC supply. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: IS:10512-2003 This instrument is used for the determination of the paraffin wax content of bitumen and bituminous binder by distillation. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer. IS:10512-2003 This instrument is used for the determination of the paraffin wax content of bitumen and bituminous binder by distillation. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: EN 1427 | ASTM D36 | AASHTO T53 | IP 58 | IS 1205 The fully automatic ring and ball capable to conduct the entire test automatically. You just have to place samples and press start button, everything else will be taken care off by the Instrument itself. Machine is capable to conduct the test with water and glycerin. Automatica rise of the temperature at 5°C per min. The Instrument will stop automatically once the ball touches the bottom of the stand and freeze the temperature at that time. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: Double walled water bath. Inner chamber is made of mirror polished stainless steel material S.S. ‑ 304 Grade, Exterior body is fabricated from Mild steel material, which is powder coated in attractive shades. Temperate ranges from : 5 °C above ambient to 100 °C, Temperature accuracy will be of ± 0.5 °C. Detailed specification as follows: Salient Features : Double walled water bath Inner chamber is made of mirror polished stainless steel material S.S. ‑ 304 Grade Exterior body is fabricated from Mild steel material, which is powder coated in attractive shades. The gap between the inner chamber and exterior body is filled with glass wool insulation to prevent the thermal heat loss Temperature inside the bath is controlled by Microprocessor based Auto‑tune Digital temperature controller cum indicator. Temperate ranges from : 5 °C above ambient to 100 °C, Temperature accuracy will be of ± 0.5 °C The bath is also fitted with a constant speed stainless steel stirrer to maintain uniform temperature distribution within the bath chamber. The bath is so designed that it can accommodates at least 3 Nos. of 6" diameter (150 MM) marshal moulds and breaking head assembly on heavy platform. Working size ‑ 15" X 15" X 6" Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: EN 1427 | ASTM D36 | AASHTO T53 | IP 58 | IS 1205. The apparatus consist of a Glass beaker made up of heat resistant glass having internal diameter of 8.5 cm and 12 cm depth (approximately). The heater is controlled by a programmable Digital Auto‑tune PID Temperature Controller Cum Indicator to ensure rise of temperature at 5° C as per the guidelines of ASTM/ISO/AASTHO/IS Standards. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: ASTM D5581 The Marshal Mould with outside dia of 6.5" (165.1mm) and inside dia of 6"(152.4mm ± 0.2mm), Mould having inside diameter by 4.5"(114.3 mm ± 0.3mm) in height, base plates, and extension collars will conform to the details shown in Fig. 1 of ASTM D5581. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: Lab technicians no longer need to rely on scraping, wire brushing, or hand heating to clean bitumen from the glassware. Operators can simply place everything in their pyrolytic oven, press start, and allow the machine to do the work. This not only reduces mess, but saves time and creates a safer, more efficient lab environment. Maximum oven temperature is 482°C and cleaning temperatures range from 426°C to 482°C to burn off organic contaminants, leaving behind only carbonized residue, which can be easily removed. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: ASTM D445,IP 71,ASTM D446 Also availabe with : 2 Viscometer, 3 Viscometer, 4 Viscometer, 6 Viscometer and 8 Viscometer. Used to determine the viscosity of oils and fuel, above room temperature up to a maximum of 120 °C. Generally used @ 40°C but can also be used at any other temperature between measuring range. Can also be used for other application where full visibility of sample and constant temp. is important for the test. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: ASTM D 5404 / D5404M - 21, IS 18130 : 2023 Standard Practice for Recovery of Asphalt Binder from Solution Using the Rotary Evaporator. Applications for Recovery of Asphalt Binder from Solution . The solution of bitumen and solvent from a prior extraction is distilled by partially immersing the rotating distillation flask of the rotary evaporator in a heated oil bath. The solution is subjected to a partial vacuum and a flow of nitrogen gas or carbon dioxide gas. These gases provide inert atmosphere to prevent oxidation of the bitumen during the recovery process Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance With Following National / International Standards: EN 1427 | ASTM D36 | AASHTO T53 | IP 58 | IS 1205 Availabe in various models such as : 1) Programmable Magnetic Stirrer Cum Heater, 2) A.C. Motorized Stirrer with Electrical Heating, 3) D.C. Motorized Stirrer with Electrical Heating , 4) Fully Automatic Operation and 5) Hand Operated - For Two Test Further details available on our website. Note : Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Enhance your concrete testing capabilities with our premium Concrete Cube Moulds. Manufactured with precision in Mumbai, India, these ISI standard moulds ensure accurate and reliable results every time.
Our Laboratory Equipment Manufacturer produces top-of-the-line lab equipment exported globally for its precision and quality. From Kenya to the USA, our products excel in accuracy.
Globetrek's woven wire mesh sieves are essential for laboratory sampling and particle size analysis. Available in various diameter sizes and aperture ranges, these sieves are crafted from high-quality materials.
Purpose Used to determine the viscosity of oils and fuel, above room temperature up to a maximum of 120 °C. Generally used @ 40°C but can also be used at any other temperature between measuring range. Can also be used for other application where full visibility of sample and constant temp. is important for the test. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer
