Search
The instrument is in accordance with People's Republic of China Ministry of Transportation standards JTG E20-2011 Standard Test Methods for Bitumen and Bituminous Mixtures for Highway Engineering in T 0755-2011 " Slurry mixture load wheel sticky sand test " provisions of the design and manufacture of it. Suitable for controlling the upper limit of the amount of asphalt in the slurry mixture, and determining the optimum asphalt content of slurry mixture with wet wheel wear test. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance with Following International Standards: IP 72, IS 1206 and BS 3235 As per IP 72, IS 1206 and BS 3235, Electric heated with Digital Temp. Controller & Indicator with F.H.P Motor Stirrer & lighting arrangement. Supplied without Stop watch, Flask receiver and IP/ASTM Glass Thermometers. These are quoted separately and available at extra cost Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance with following international standards: IP 34, ASTM D‑93, IS ‑ 1448 and IS ‑ 1209 Basic Model. These test methods cover the determination of the flash point of petroleum products in the temperature range from 40 to 360° C by a manual Pensky Martens Closed Cup Apparatus. The apparatus serve the purpose according to IS 1209 1958 method A. The apparatus consists of a Brass Test cup with handle, removable cup cover with spring operated rotating shutter having Oil pilot jet, stirrer with flexible shaft (not-motorized). With energy regulator for temperature regulation, Suitable for operation on 220 volts AC mains. Open clip, IP Glass Thermometers, Gas test jet device available at extra cost. To Satisfy the requirements as per IS:1209 Part B and Part C, motorized stirrer and open clip are needed and available at extra cost. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Asphalt Mixer Vertical, 20lt. machine mainly consists of a main frame, variable speed mixer, elevating system, heating pot, electrical control box. The variable speed mixer consists of electric motor, gear box and vertical curved blade. The elevating system consists of a motor, worm gear, up right column,guide bar and stopper block and the heating pot has a double lever metal pot, conduction coil and electric heater. In vertical type of mixer the pot can move up and down and in the horizontal type of mixer the elevating system with agitator assembly moves up and down. Suitable for operation on 230 V, 50 Hz, 1 phase, AC supply. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following International Standards: IS:516, BS:1881 and ASTM C78 Automatic Test Execution: Once the machine has been switched on, the specimen positioned and centered, the only required operations are: Set test parameters including load rate: Press the start button The machine automatically: starts the rapid approach; switches to the test speed once the specimen comes into contact with the upper platen; automatically stops the motor upon specimen failure Save the test including data results . The test execution conforming to Standards can be easily proved. Working on 240V, 50 60Hz, single phase. Dual stage pump assuring fast piston approach and precise test execution Test execution conforming to EN 12390-5, ASTM C78, AASHTO T22 Controllable pace rate from 0.03 KN/Sec to 10 KN/Sec. Auto stop after completion of each test. Soft platen to specimen contact and smooth load rate control from the very beginning of the ramp Servo motor driven machine Auto calculation of the flexural strength after the failure of the sample. Calculation is done after failure of the sample by sending the distance of the nearest roller from the crack. Frame: High stiffness welded frame tested for stability. Heavy duty spherical seat, allowing initial free alignment at the initial contact with the specimen and automatic jamming up to the end of test. Piston travel limit switch (Extra cost) Emergency stop button Servo motor driven machine Gives live online graph on the 7" touch screen User friendly large graphical display Saves 50 results in the 7" touch screen Inbuilt USB drive to save the data. Salient fetchers of data manager PC software (Optional at extra cost.): Two way communication i.e machine operates from computer and from the touch screen controller both (Stat, stop, save data and save graph) Results directly saved in excel file. Graph also saved in excel file. Capable to save customer name, other details of customer, ageing of beam moulds, identification mark of the beam moulds, date and time of testing Capable to print direct report from the computer. Capable to select different test parameters like pace rate, sample size and area from the computer (software) Capable to select different type of tests, like flexural, CTM, aggregate crushing etc. Note: It is recommended to use the machine with 3 KVA servo stabilizer The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance With Following National / International Standards: IS:10512-2003 This instrument is used for the determination of the paraffin wax content of bitumen and bituminous binder by distillation. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer. IS:10512-2003 This instrument is used for the determination of the paraffin wax content of bitumen and bituminous binder by distillation. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following International Standards: EN 12390-4, ASTM C39, AASHTO T22, IS : 14858 (2000) Manufactured as per International design, Plate model for highest mechanical stability, accurate centering of load and excellent repeatability. Fully Automatic pace rate control, auto stop and auto release on failure of test specimen, can be attached with flexural load frame or 500 KN load frame. attachment for Split tensile test, Modulus of Elasticity also available. Please visit YouTube video of the machine by clicking on this link https://youtu.be/9n-Ac_T_18k Note - Price and specifications mentioned here indicative only and are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Heating & Cooling System Long lasting SS tubular heaters used as heating element. The stainless steel fins provided to ensure better heat transfer. Hermetically sealed compressor CFC free compressor (134 A gas) coupled with evaporation coil and condenser Control Microprocessor based Digital Auto-Tune PID temperature and direct RH digital controller. Humidity directly measured in % RH by electronicsensor. Technical Specifications Construction : Sandwich type. Inner chamber : Stainless steel S.S.-304 Grade. Exterior body : Mild steel. Paint : Powder coating in attractive shades. Thermal insulation : 75mm to prevent thermal loss. Chamber Dimension : 600 mm X 600mm X 600mm. Chamber Volume : 200 liter. Optimum Performance : with 150 kg of Concrete load. Temperature range : 5°C above Ambient to 60°C. Humidity range : Ambient to 80% RH(Maximum carbonation takes place between 40% RH to 80% RH ). CO2 Concentration : Atmosphere concentration to 4.5% with accuracy 0.01%. (Maximum solubility of CO2 in water is 4%). Controller : Digital PID Temp & RH Controller Safety Features High temperature safety cut off. Low water level boiler cut off. Electrical overload cut off. Time delay for compressor switch ON. Electrical circuit breake. Applications It is used for testing the durability of concretes under an environment of constant temperature, humidity and CO concentration, which is a 2 special apparatus for carbonation test of concretes. Salient Features Double wall construction. Interior fabricated from high grade stainless steel (S.S.304). Exterior body made of Mild steel material - which is duly. powder coated in attractive shades. Double walled metal door with sponge - type silicon gasket for air-tight sealing. Chamber illumination is accomplished by Fluorescent light with door switch. Cord wire duly tested and inspected with stress factor as per CE standard. Electric Motor located at the back side of unit, protected with safety cover to avoid accident. Standard motor of reputed Make. User friendly and tactfully designed chamber door and locking mechanism. Aesthetic outer appearance and high quality. Air Circulation Temperature is maintained by a quiet running blower circulation air throughout the chamber. Forced air circulated vertically down and re circulated throughout the chamber for uniform temperature and humidity. Note - Price will be change as per specification
Compliance With Following International Standards: EN 12390‑4, ASTM C39, AASHTO T22, IS : 14858 (2000) Once the machine has been switched on, the specimen positioned and centered, the only required operations are Set test parameters-including load rate: Press the start button Tighten the pressure valve The machine automatically: starts the rapid approach; switches to the test speed once the specimen comes into contact with the upper platen; automatically stops the motor upon specimen failure Release the pressure valve The test execution conforming to Standards can be easily proved. Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance With Following International Standards: AS PER BS 1881 PART 5: This apparatus is used to assess the surface absorption characteristics of concrete.The rate of flow of water per unit area into a concrete surface when subjected to a constant head of 200 mm is measured. The unit consists of a capillary tube mounted on a scale, a water reservoir & connecting tubes. Easy to use, mounted on a stand. As per BS 1881: Part 208:1996 Weight : 30 kg Approx. Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance With Following National / International Standards: ASTM D 1559 , ASTM D 6926; AASHTO T245 It is a motor driven mechanical compactor useful for compaction in to 4" dia Marshal moulds. It is fitted with a compaction rammer weighing 4.5 kg. with a free fall of 457 mm. The rammer assembly is provided with a ratchet and pawl arrangement to lift it from the top of the test sample. When the rammer reaches the required height the pawl release the rammer which falls freely on test specimen. The release mechanism is connected by an arm moving up and down which is connected to a reduction gear coupled to the motor through another arm. An automatic blow counter fitted to the compactor is used to set the number of blows. Supplied without Moulds. - Available at extra cost Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following International Standards: EN 12390-4, ASTM C39, AASHTO T22, IS : 14858 (2000) Manufactured as per International design, Plate model for highest mechanical stability, accurate centering of load and excellent repeatability. Fully Automatic pace rate control, auto stop and auto release on failure of test specimen, can be attached with flexural load frame or additional load frame. attachment for Split tensile test, Modulus of Elasticity also available. Please visit YouTube video of the machine by clicking on this link https://youtu.be/9n-Ac_T_18k Note - Price and specifications mentioned here indicative only and are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following International Standards: ASTM C403, IS:8142, IS:1199-part 7 Used to determine the elapsed time between batching of a concrete sample and when it is deemed by standard methods to have set. The method involves measuring the penetration resistance of a test sample, which has had coarse particles removed at periodic intervals. It is particularly useful, in determining the effect on setting time of admixtures in the concrete, where these may have been introduced specifically to increase the setting time. Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance With Following International Standards: ASTM C1621 Introduction: Fill box is one of the apparatus of the SCC (Self Consolidating Concrete) test accessories. These tests are used to determine the flowability and passing ability of Self-Consolidating Concrete (SCC) as defined in ASTM C1621. Passing ability refers to the ability of SCC, under its own weight (without vibration), to flow into and completely fill the spaces within an intricate framework, containing obstacles such as reinforcement bars. Application of Fill box test method for SCC: This test is also known as ‘Kajima test’. The test is used to measure the filling ability of self compacting concrete with a maximum aggregate size of 20 mm. Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance With Following National / International Standards: ASTM C231 - TYPE B, BS-1881-106, AASHTO T152, EN 12350-7, IS 1199 (Part - 4) Pressure Gauge method (Clause 4.4) Details: Accurate, high-quality, and easy to use for testing air-entrained concrete Lightweight, compact and durable Allows quick clamping system and testing with few pump strokes. Consists of an aluminum cylindrical vessel with airtight cover assembly Assembly also incorporates an air pump, a precision pressure gauge and valves. Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance Standards: IS 516, IS 10086 - ISI MARKED, ALSO AVAILABLE AS PER BS EN 12390-1, EN 12390-3 Details: Made of Cast Iron, with base plate, the faces are machined flat to ± 0.02mm accuracy and finished to within ± 0.2mm of specified dimensions. The moulds will be stout enough to prevent distortion. It will be constructed in such a manner as to facilitate the removal of the molded specimen without damage and will be so machined that, when they are assembled ready for use, the dimensions and internal faces shall be accurate within the specified limits. Internal faces of the moulds will be smooth. The base plate will be attached to the mould by cleats or secured with threaded studs and nuts/wing nuts. Weight of the mould will be about 13.5-14.0 kg. Strictly as per BIS specifications and within required tolerance. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance With Following International Standards: ASTM C31, C192, C617, AASHTO T-23, T-126, IS: 516, BS 1881-120 When testing concrete cylinder specimens it is essential that the two ends are perfectly flat. EIE Capping set allows the ends of the various sizes of concrete cylinders (100 or 150 mm) or cores to be capped using the sulphur capping compound. Melting Pot, Cylinder carrier, Capping compound available at extra cost.Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
The manhole cover testing machine is designed as per IS 12592. The machine will be able to accommodate manhole cover of 1200 mm x 1200 mm size. With variable pace rate of the machine from 2 kN / sec to 10 kN / sec. The machine with digital read out, showing actual load, peak load and permanent set. The Machine is also available to accommodate sample size of 1500 X 1500mm with Load Capacity 1000 KN. Fully automatic Machine is also available. Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance With Following International Standards: ASTM C666 The Rapid Freeze Thaw Cabinet is used to measure the resistance of concrete to deterioration caused by repeated cycles of freezing and thawing in water. The system is designed to test up to eighteen 3" x 4" x 16" (76 x 102 x 406 mm) concrete specimens simultaneously, with one being a control. Fully automatic operation frees operator to perform other lab duties. Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance With Following Standards: Compliance Standards : IS : 2514 For compaction of concrete cube cylinders. The table deck size has stops along its edges to prevent moulds from walking off the table during operation. The variable pitch pulley arrangement permits the frequency to be varied steplessly between maximum of 3600 vibrations down to 2600 vibrations per minute. A speed regulation handle is provided for increasing or decreasing the frequency. The vibrator is mounted on cushioned steel vibrating deck. A switch is provided for starting the motor. Operation on 440 V, three phase, A.C. supply. Also available in Table size 60x60, 75x75, 100x100, 120x120, 120x150, 200x100cm Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Designed for mixing small quantities of concrete used in preparation of concrete cubes for testing in Laboratories. The purpose of the mixer is to smear mechanically the aggregate surface with cement paste uniformly and produce a mix of uniform consistency. This in turn gives consistent quality of cube specimens when casted in the moulds. Also avaible in 60 Litres/80 Litres/100 Litres Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance With Following National / International Standards: EN 196-6, ASTM C204, BS 4550 This test method concerns the determination of the particle size of Portland cement, limes and similar powders using the Blaine air permeability apparatus. The measure of fineness is expressed in terms of the specific surface area (the total particle surface area) in square centimeters per gram or square meters per kilogram Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance With Following International Standards: ASTM C230, ASTM C1437 Also available in M.S. Steel Top. The flow table consists of a brass table top 250 ± 2.5 mm dia mounted on a rigid stand. The table top is reinforced with equally disposed ribs and allowed to drop through 12 mm by a ground and hardened cam, Complete with mould - 100 mm base dia, 70 mm top dia and 50 mm high. Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance With Following International Standards: IS 5512 Also available in M.S. Steel Top. Flow table consist of a brass table top 250 ± 2.5 mm dia mounted on a rigid stand. The table top is reinforced with equally disposed ribs and allowed to drop through 12 mm by a ground and hardened cam, Complete with mould- 100 mm base dia, 70 mm top dia and 50 mm high. The cam shaft is rotated at the rate of 100 RPM by an electric motor. Suitable for operation on 230 Volts 50 cycles. Single Phase, A.C.Supply. Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Photometric test Apparatus for quick determination of SO3 in cement. The Model is provided with double light intensity meter, as such useful where the % of SO3 is desired to be known with higher accuracy. The Model is of export quality & provided with constant voltage Transformer built in. Beside this the component used in is of the highest quality available in market. Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance With Following International Standards: IS : 9013 Accelerated Curing Tank having capacity to accommodate 3 Nos. concrete cube moulds of 15 cm with a facility for accelerated curing by boiling water method up to temperature range : 100 ± 2 °C as per IS standard IS : 9013. Also it will have capacity for curing by warm water method at temperature 55 ± 2 °C. Also available in various models. Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance With Following National / International Standards: ASTM D445,IP 71,ASTM D446 Also availabe with : 2 Viscometer, 3 Viscometer, 4 Viscometer, 6 Viscometer and 8 Viscometer. Used to determine the viscosity of oils and fuel, above room temperature up to a maximum of 120 °C. Generally used @ 40°C but can also be used at any other temperature between measuring range. Can also be used for other application where full visibility of sample and constant temp. is important for the test. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: ASTM D 5404 / D5404M - 21, IS 18130 : 2023 Standard Practice for Recovery of Asphalt Binder from Solution Using the Rotary Evaporator. Applications for Recovery of Asphalt Binder from Solution . The solution of bitumen and solvent from a prior extraction is distilled by partially immersing the rotating distillation flask of the rotary evaporator in a heated oil bath. The solution is subjected to a partial vacuum and a flow of nitrogen gas or carbon dioxide gas. These gases provide inert atmosphere to prevent oxidation of the bitumen during the recovery process Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance With Following National / International Standards: The Fraass breaking point method provides a measure of the brittleness of bitumen and bituminous binders at low temperatures. A bituminous binder sample is spread on a thin steel blade to a uniform thickness, this blade is subjected to constant cooling and flexed repeatedly until the binder layer cracks. The temperature at which the first cracking appears is noted as the Fraass point. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: EN 1427 | ASTM D36 | AASHTO T53 | IP 58 | IS 1205 Availabe in various models such as : 1) Programmable Magnetic Stirrer Cum Heater, 2) A.C. Motorized Stirrer with Electrical Heating, 3) D.C. Motorized Stirrer with Electrical Heating , 4) Fully Automatic Operation and 5) Hand Operated - For Two Test Further details available on our website. Note : Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: IS 1206 (Part II) and (Part III), ASTM D2171, ASTN D2170, EN 12596 As per IS: 1206 (Part II and III).Supplied complete with Viscosity bath with built in Digital stop watch, Vacuum Pump - capable to maintain vacuum of 300 mm/Hg, Indian Make Vacuum Manning Viscometer No.12 and 13, Reverse flow Viscometer No.6, Silicon oil, silicon tubes and calibration certificate for Viscosity bath, certificate of constant for Viscometers. Complete with instruction manual. Detailed Specification as mentioned in technical part mentioned below. Canon USA Make Glass U Tube Viscometer, Mercury Manometer, Digital Vacuum Indicator cum controller etc. are available at extra cost Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: As per IS 1203. As per IS 1203. Basic Model with fine adjustment facility for ease of precise setting.. As per IS 1203. The apparatus consist of a cast aluminum base with an iron stand on which moves an aluminium arm. A 6" dial is fixed on this arm and a brass chromium plated rod slide through the lower portion of the arm. A needle with weights is fitted to this rod. The dial is graduated from 0‑400 in one tenth millimeter sub division. Supplied complete with adjustable needle holder, penetration needle, sample container, transfer dish and weight of 50 gm. Digital stop watch is essential to perform the test at extra cost. Model with Automatic controller and fine adjustment facility also available. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: IP‑49,IS‑1448 This apparatus is used for penetration test on a wide variety of materials such as grease, petroleum, Bitumen, Tar, Wax, Polish, foodstuff, rubber asphalts and Pharmaceutical creams. A depression is made in the sample by a needle of a definite weights which is measured intenths of a millimeter and expressed as penetration number. The apparatus consist of a cast aluminium base with an iron stand on which moves an aluminium arm. A 6" dial is fixed on this arm and a brass chromium plated rod slide through the lower portion of the arm. A needle with weights is fitted to this rod. The dial is graduated from 0‑400 in one tenth millimeter sub division. Supplied complete with adjustable needle holder, penetration needle sample container, transfer dish and weight of 50 gms. Without automatic DIGITAL timer with electrical arrangement. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: ASTM D937, IS 1508, IS 4887, IP 179, ISO 2137 Details The Penetrometer is so designed that it permits the specified cone to drop vertically at least 40 mm and indicates accurately the depth of Penetration to nearest 0.1 mm. The Penetrometer has a platform to accommodate the test sample which can be adjusted horizontally before making the test and a mechanism for releasing the clamp of the loaded cone. The Cone is made of brass with detachable hardened steel tip, constructed to conform to the dimensions and tolerances shown in Fig. 1 of IS : 4887. The total weight of the cone and its movable attachments will be 150.0 ± 0. 1 g. The attachments consist of a rigid shaft having a suitable device at its lower end for engaging the cone. The outer surface is polished to a very smooth finish. Supplied with 1 No. each Cone, sample container and weight. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: EN 1427 | ASTM D36 | AASHTO T53 | IP 58 | IS 1205. The apparatus consist of a Glass beaker made up of heat resistant glass having internal diameter of 8.5 cm and 12 cm depth (approximately). The heater is controlled by a programmable Digital Auto‑tune PID Temperature Controller Cum Indicator to ensure rise of temperature at 5° C as per the guidelines of ASTM/ISO/AASTHO/IS Standards. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: ASTM D 2172, AASHTO T58, AASHTO T164, EN 12697-1 SPECIAL MODEL WITH AC MOTOR AND DRIVE : This model facilitates precise speed control and vibration free smooth operation. Speed variation up to 3600 RPM. Complies with following International Standards - ASTM D 2172, AASHTO T 58, T 164. Electronic weighing Balance, Filter Paper and solvent are available at extra cost. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: IS : 1208, ASTM D 113, ASTM D5892, ASTM D6084, AASHTO T51 Ductility is defined as distance in (cms) to which a standard briquette of bitumen can be stretched before the thread breaks. The briquette is stretched at a rate of 50 mm/min ± 2.5 mm/min at a temperature of 27° C ± 0.5° C Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: Oven is designed to determine the the effect of heat & air on asphaltic materials (thin film test).The unit is heavily insulated & has a double glass built in door for view inside temperature is controlled at 163°C ± 1°C. by means of a calibrated PID based DIGITAL TEMP. INDICATOR CONTROLLER. Inside Suspended a 340 mm dia rotating platform having provision to keep 4 Nos. sample containers of 140 mm ID X 10 mm Internal depth, rotated by external motor from 5 to 6 R.P.M. (supplied with cups). Inner chamber made of stainless steel sheet of 304 grade & outer of mild steel sheet ‑ powder coated. To work on 230 volts, AC 50 Hz supply. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Enhance your concrete testing capabilities with our premium Concrete Cube Moulds. Manufactured with precision in Mumbai, India, these ISI standard moulds ensure accurate and reliable results every time.
Globetrek's woven wire mesh sieves are essential for laboratory sampling and particle size analysis. Available in various diameter sizes and aperture ranges, these sieves are crafted from high-quality materials.
Transformer: EI Transformer Cooling System: Air cooled Input Voltage: 115-280V Output Voltage: 220/230 +_ 10% Efficiency: >98% Technology: Zero Cross switiching technology/Digital CPU & delay countdown system Display: Volt Meter Protection: High voltage/low voltage/3s output delay Operating Condition: 0-45 C non condensing Phase: Single Phase Power: 500VA
Transformer: EI Transformer Cooling System: Air cooled Input Voltage: 170-270V Output Voltage: 220/230 +_ 10% Efficiency: >98% Technology: Zero Cross switiching technology/Digital CPU & delay countdown system Display: Volt Meter Protection: High voltage/low voltage/3s output delay Operating Condition: 0-45 C non condensing Phase: Single Phase Power: 5000VA
Transformer: EI Transformer Cooling System: Air cooled Input Voltage: 170-270V Output Voltage: 220/230 +_ 10% Efficiency: >98% Technology: Zero Cross switiching technology/Digital CPU & delay countdown system Display: LED Display Protection: High voltage/low voltage/3s output delay Operating Condition: 0-45 C non condensing Phase: Single Phase Power: 150VA
Discover our extensive catalog featuring a diverse array of high-quality mechanical and electric parts meticulously crafted for a myriad of applications across industries. From precision-engineered components ensuring optimal performance to durable materials guaranteeing longevity, our products are designed to meet the rigorous demands of modern manufacturing and technology. Whether you require intricate gears, robust motors, or sophisticated circuitry, we offer reliable solutions to suit your needs. With a commitment to excellence and customer satisfaction, we strive to provide unmatched value and service. Partner with us for your mechanical and electric part requirements and experience the difference in quality and reliability.
Voltage fluctuations can harm your air conditioner and reduce its life cycle. IFB's range of digitally controlled, state-of-the-art voltage stablizers are here to protect and safeguard your comfort.
800F PB, 22mm Selector Switch, Selector Switch, No Power Module (Lamp Type), Maintained, 2 Position, No Power Module, Monolithic, No Power Module (Voltage), Screw, Black Knob, No Knob Orientation, 1 N.O. Monolithic Circuit More Details
800F 3 Position Selector Switch - Plastic Monolithic, Maintained, Black, Standard Knob, More Details
Voltage fluctuations can harm your air conditioner and reduce its life cycle. IFB's range of digitally controlled, state-of-the-art voltage stablizers are here to protect and safeguard your comfort.
